| RomRaider https://mailserver.romraider.com/forum/ |
|
| HELP! im out of ideas, cut at peak torque https://mailserver.romraider.com/forum/viewtopic.php?f=36&t=21202 |
Page 1 of 1 |
| Author: | terryjr [ Thu Apr 11, 2024 6:58 pm ] |
| Post subject: | HELP! im out of ideas, cut at peak torque |
Cant post much since its a protune, one of the biggest names in game. But I'm stumped and dealing with a protuner has been a struggle. Short back story, i put a base map on it spent a good bit of time dialing in idle, warm up, cruise, stuff like that. Ran great so brought it in after break in for the big tune. Ran solid on dyno, made 604whp, revved out to 8500 rpm on e55. Current situation. topped of a few days later with flex fuel, e66 in there now and its now revving to redline anymore. Its got a cut like you turned the key off. It doesnt seem to be a certain rpm or even boost, just seems to be at peak torque. Usually around 30.5 to 32psi and between 5,000 and 6300 rpm. Let off throttle and it drives normal again. Naturally i suspected a boost cut but its under the cut point. got a revised rom from tuner, still did it. Tried my old rom, still did it. So im leaning towards a hardware issue but dont know. Maybe the ignition drivers in ecu, is that a thing? Its not a hard cut either like a fuel or igniton cut, its a very soft, since it doesnt come back on til you lift. spec that matter: New purple exotruck. ej20, 02 usdm wrx ecu, carberry 4.2, no dtc's, cobb 4 bar map, cobb 3 port, grey coils, bkr7eix plugs, new oem knock, brand new iwire harnesses top to bottom, flex sensor on rear o2. practically same exact setup thats in my trouble free OG truck log, but doest show too much https://datazap.me/u/terryjr/purple-cut ... ata=2-6-11 |
|
| Author: | gaby [ Thu Apr 11, 2024 7:06 pm ] |
| Post subject: | Re: HELP! im out of ideas, cut at peak torque |
What is your fuel pressure and your AFRs? Sent from my iPhone using Tapatalk |
|
| Author: | terryjr [ Thu Apr 11, 2024 7:48 pm ] |
| Post subject: | Re: HELP! im out of ideas, cut at peak torque |
gaby wrote: What is your fuel pressure and your AFRs? Sent from my iPhone using Tapatalk mid 11's on target. pressure i dont know but its got twin 450 pumps |
|
| Author: | zero knowledge [ Fri Apr 12, 2024 4:41 am ] |
| Post subject: | Re: HELP! im out of ideas, cut at peak torque |
In second and third log MAP sensor shows vacuum during WOT. Just before that AFR goes leaner from 11 to 12+ |
|
| Author: | terryjr [ Fri Apr 12, 2024 9:43 am ] |
| Post subject: | Re: HELP! im out of ideas, cut at peak torque |
zero knowledge wrote: In second and third log MAP sensor shows vacuum during WOT. Just before that AFR goes leaner from 11 to 12+ ya it adds to the mystery, i dont know how it can show vacuum with throttle wide open |
|
| Author: | terryjr [ Thu Apr 18, 2024 3:56 pm ] |
| Post subject: | Re: HELP! im out of ideas, cut at peak torque |
problem sorted. it was the silicone turbo inlet sucking shut |
|
| Page 1 of 1 | All times are UTC - 5 hours [ DST ] |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|