MSS52 Definitions

Lambda1 · **Joined:** Sat Jan 14, 2017 9:46 pm **Posts:** 534

In my opinion share if you like to share

.
Also be good to rework bricked one to check, remap and if you got master and slave reads to share them.
You can change vin if you want and also Virgin them... So there is also no problem.

heeveycc · **Joined:** Wed Nov 22, 2017 6:15 am **Posts:** 8

Code:

<table type="2D" name="Warm-up Lights" category="Config Switches" storagetype="int8" endian="big" sizex="8" userlevel="1" >
   <scaling units="deg C" expression="x-48" to_byte="x+48" format="0" fineincrement="1" coarseincrement="5" />
   <table type="Static X Axis" name="Light" sizex="7">
      <data>light 1</data>
      <data>2</data>
      <data>3</data>
      <data>4</data>
      <data>5</data>
      <data>6</data>
      <data>7</data>
   </table>
   <description>Warmup Light Segments</description>
</table>

Code:

   <table name="Warm-up Lights" storageaddress="0x5510">
   </table>

<3

heeveycc · **Joined:** Wed Nov 22, 2017 6:15 am **Posts:** 8

Code:

<table type="2D" name="Gear Ratios" category="Config Switches" storagetype="uint8" endian="big" sizex="8" userlevel="1" >
   <scaling units="Ratio" expression="x/60" to_byte="x*60" format="0.00" fineincrement="1" coarseincrement="5" />
   <table type="Static X Axis" name="Gear" sizex="8">
      <data>Final Drive</data>
      <data>1</data>
      <data>2</data>
      <data>3</data>
      <data>4</data>
      <data>5</data>
      <data>6</data>
      <data>Reverse</data>
   </table>
   <description>Gear Ratios</description>
</table>

if someone can share a good .OLS with me? I can do more. Thanks

heeveycc · **Joined:** Wed Nov 22, 2017 6:15 am **Posts:** 8

ALSO WOT ENRICH IS OFF:

Code:

storageaddress="0xB2A">

Johnny_B · **Joined:** Thu May 28, 2015 5:27 pm **Posts:** 87

is there a possibility to turn the AC off in config switches?
here is the thing - engine swapped into e36 with stock ECF from donor car e39 m5, but after engine start, fan starts spinning at maximum speed.
Car does not have AC.
My guess - it's some kind of protection, because engine doesn't detect pressure in AC system, and it starts spinning an ACF to prevent AC system damage.
So I looking for possibility to swich the AC off permanently.

Lambda1 · **Joined:** Sat Jan 14, 2017 9:46 pm **Posts:** 534

Some know location for changing speed signal recognition from abs sensors to cluster speed or differential signal like mss54 guys can do?
Or should I search by my own?
Need for registration to limit speed :/ in mine new build E30 S62. So also can be use cruise control in e30

.

@heeveycc did you define more switches ... ?

pazi88 · **Posted:** Wed Feb 06, 2019 8:41 am

Lambda1 wrote:

Some know location for changing speed signal recognition from abs sensors to cluster speed or differential signal like mss54 guys can do?
Or should I search by my own?
Need for registration to limit speed :/ in mine new build E30 S62.

@heeveycc did you define more switches ... ?

I can check if I would find that one

Lambda1 · **Joined:** Sat Jan 14, 2017 9:46 pm **Posts:** 534

Maybe someone can confirm.
Partial 6094, 02=default, 00= from cluster or diff (same as in mss54).

speedometer calibration
partial 6086 ?

Johnny_B · **Joined:** Thu May 28, 2015 5:27 pm **Posts:** 87

Lambda1 wrote:

speedometer calibration
partial 6086 ?

Yes.

ChrisSE39 · **Joined:** Wed May 01, 2019 9:44 pm **Posts:** 1

Hi all,

Been reading alot of thread on many various forums the last few day, and just wanted to say thank you!

I am looking to make adjustment to my WOT timing, and was wondering if there were any further developments there?

Chris

Lambda1 · **Joined:** Sat Jan 14, 2017 9:46 pm **Posts:** 534

everything is there for...

ve2zyc · **Joined:** Sat Jun 15, 2019 2:28 pm **Posts:** 12

Hi guys,

I try do do a little addon for the SAI delete (DTC 170) with a switch as you did with the EWS Delete and the Sport mode button. My hex adress is right but the thing won't work. Is there a bug in my code?

Code:

<table type="Switch" name="SAI Delete" category="Config Switches" sizey="2" userlevel="5">
   <state name="SAI - Disable" data="28 00" />
   <state name="SAI - Enable" data="28 27" />
   <description>Use this switch to disable Second Air Pump (DTC 170)</description>
</table>

Code:

Also, I took your XLM and did an adaptation for the 0601 DME version if someone need it, let me know.

ve2zyc · **Joined:** Sat Jun 15, 2019 2:28 pm **Posts:** 12

Here is an update xml def file to support 0601 and 1701 version of mss52 as well of 1601. Thanks to ba114 for your work it helped a lot to being able to get it done.

BUT I did 3 addition switch and they wont work, if someone find why please tell me.
Those are:
SAI Delete
Ebox fan
CAT Delete

The xml code seems to be good but when I do the mod, save, close and reopen the .bin, then the change havent really happen. So I tried doing the change manually (example for SAI Delete) with an hexeditor and when I open back the file with RR and chose the SAI Delete option it show the right thing, so my addresses are good.

Code:

<table type="Switch" name="SAI Delete" category="Config Switches" sizey="2" userlevel="1">
   <state name="SAI - Enable" data="28 27" />
   <state name="SAI - Disable" data="28 00" />
   <description>Use this Switch to disable second air pump (DTC 170)</description>
</table>

<table type="Switch" name="Ebox fan" category="Config Switches" sizey="2" userlevel="1">
   <state name="Ebox fan - Disable" data="28 00" />
   <state name="Ebox fan - Enable" data="28 03" />
   <description>Use this switch to disable Ebox fan (DTC 143)</description>
</table>

<table type="Switch" name="CAT Delete" category="Config Switches" sizey="28" userlevel="1">
   <state name="Post o2 sensor - Disable" data="B2 01 01 01 01 01 01 00 01 2F 33 28 00 FF B3 01 01 01 01 01 01 00 01 30 34 28 00 FF" />
   <state name="Post o2 sensor - Enable" data="B2 01 01 01 01 01 01 00 01 2F 33 28 25 FF B3 01 01 01 01 01 01 00 01 30 34 28 25 FF" />
   <description>Use this switch to disable rear o2 sensor (post cat) when you remove catalytic converters(DTC 178 - 179). 
You have to keep the o2 sensor connected, sensor heater circuit will give you a CEL if you disconnect them.</description>
</table>

Thanks for your help!

ve2zyc · **Joined:** Sat Jun 15, 2019 2:28 pm **Posts:** 12

I found the issue, the parameter was at 2 place in the XML, so updating it at one place was not updating it at the other.

I will update it with new versions as I add/modify things.

ve2zyc · **Joined:** Sat Jun 15, 2019 2:28 pm **Posts:** 12

Here is the version 4

contain:
software v 0601,1601,1701
3 DTC delete methods
i suggest beginning with method 1, if it dont work then 2, then 3

EWS Delete
EWS communication DTC 66
EWS tampering DTC 130
EWS interface DTC 148

software v 1601,1701
IAT (relative filling vs temperature correction)
IAT maf temp correction

RomRaider

Forum rules

MSS52 Definitions

Who is online