 |
RomRaiderOpen Source ECU Tools |
|
RomRaider
Documentation
Community
Developers
|
 
|
Page 1 of 1
|
[ 7 posts ] |
|
| Author |
Message |
|
05Pzev
|
Post subject: Any chance of disabling codes on unsupported version?  Posted: Thu Jan 14, 2016 9:04 pm |
|
 |
| RomRaider Donator |
Joined: Sun Jan 03, 2016 2:05 pm
Posts: 217
|
|
I have a USDM 2005 Subaru Outback PZEV MT with ECU ID: 2F 22 0A 47 06.
I don't need to tune, I'd just like to permanently turn off an annoying P2096 code that nobody can get to the bottom of. I wouldn't mind the option of turning off other codes as well.
Is there any way to gain limited support for this ECU ID?
I'd be happy to make a donation for this ability.
Last edited by 05Pzev on Thu Jan 14, 2016 10:09 pm, edited 2 times in total.
|
|
| Top |
|
 |
|
bludgod
|
Post subject: Re: Any chance of disabling codes on unsupported version? Posted: Thu Jan 14, 2016 10:01 pm |
|
|
| Moderator |
 |
Joined: Sat Jul 06, 2013 12:55 pm
Posts: 3297
Location: NI
|
|
do you have the standard rom file to post up? If you can post the rom someone might find time to start digging into it for you.
_________________
Good luck and may the logs be ever in your favour!
|
|
| Top |
|
|
|
05Pzev
|
Post subject: Re: Any chance of disabling codes on unsupported version? Posted: Fri Jan 15, 2016 1:45 am |
|
|
| RomRaider Donator |
Joined: Sun Jan 03, 2016 2:05 pm
Posts: 217
|
|
I can't seem to figure out how to download it.
I tried EcuFlash with SH7055 and SH7058 aka sti04 and sti05 but both get an init error.
I'm not 100% sure I'm doing it correctly.
I looked at the definitions in \progra~1\openecu\ecuflash\rommetadata\subaru\outback 2.5i. i looked at all of them, the closest was an 06 2.5i which said flashmethod sti05 and memmodel SH7058 so I picked these parameters under "Select vehicle type" in EcuFlash.
Is there another approach?
|
|
| Top |
|
|
|
bludgod
|
Post subject: Re: Any chance of disabling codes on unsupported version? Posted: Fri Jan 15, 2016 9:01 am |
|
|
| Moderator |
|
Joined: Sat Jul 06, 2013 12:55 pm
Posts: 3297
Location: NI
|
|
might be worth trying the other flash methods and see if that works out for you. If you can't get the rom off the car then nobody will be able to edit it for you though.
_________________
Good luck and may the logs be ever in your favour!
|
|
| Top |
|
|
|
throttlehappy
|
Post subject: Re: Any chance of disabling codes on unsupported version? Posted: Fri Jan 15, 2016 9:58 am |
|
|
| Senior Member |
Joined: Sat Feb 12, 2011 11:27 pm
Posts: 2032
Location: Northern NSW
|
|
Both green flash connectors plugged in?
|
|
| Top |
|
|
|
05Pzev
|
Post subject: Re: Any chance of disabling codes on unsupported version? Posted: Fri Jan 15, 2016 4:37 pm |
|
|
| RomRaider Donator |
Joined: Sun Jan 03, 2016 2:05 pm
Posts: 217
|
|
Oops
I didn't have the connector attached (just 1 for me on the pax side?). I was able to download it and saved it to rom and scf.
Is it not possible to just edit this rom in EcuFlash?
Looks like it will let me edit the trouble code mappings... but not sure if that'll do it, and if it would, what the proper procedure would be.
EDIT - I think I got it. You click on the checkbox on the code and then pick "Decrement" to change it from enabled to disabled. Does that sound correct?
|
|
| Top |
|
|
|
throttlehappy
|
Post subject: Re: Any chance of disabling codes on unsupported version? Posted: Wed Feb 03, 2016 10:54 pm |
|
|
| Senior Member |
Joined: Sat Feb 12, 2011 11:27 pm
Posts: 2032
Location: Northern NSW
|
Correct 
|
|
| Top |
|
|
|
|
Page 1 of 1
|
[ 7 posts ] |
|
Who is online |
Users browsing this forum: No registered users and 3 guests |
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum
|
|
|
