CarBerry ROM - EcuFlash Definitions

mr23ik · **Joined:** Sun May 12, 2013 2:40 pm **Posts:** 3

Good job! But some maps not displayed:
CL to OL Transition with Delay BPW Hysteresis
CL Delay Maximum Engine Speed.

Artizle · **Joined:** Sun Jan 13, 2013 5:58 am **Posts:** 250

mr23ik wrote:

Good job! But some maps not displayed:
CL to OL Transition with Delay BPW Hysteresis
CL Delay Maximum Engine Speed.

Fixed

SubiSam · **Joined:** Sun Aug 17, 2008 7:45 am **Posts:** 90

SD/MAF blend mode says (no match). Can't switch from MAF to SD.

Edit: Changed modes in Romraider, then saved and opened in ECUflash. Now it works.

Dr Waffles · **Joined:** Wed Oct 23, 2013 9:42 am **Posts:** 252

siewcu · **Joined:** Sun Apr 05, 2015 11:51 am **Posts:** 2

Artizle wrote:

mr23ik wrote:

Good job! But some maps not displayed:
CL to OL Transition with Delay BPW Hysteresis
CL Delay Maximum Engine Speed.

Fixed

is it ok to tune with metric units? will it work? or should i tune with std units?

Artizle · **Joined:** Sun Jan 13, 2013 5:58 am **Posts:** 250

jaydnisevil wrote:

Fixed. Also added metric variant.

EDIT: Accidentally uploaded wrong zip originally, if you downloaded before this edit redownload

illicit · **Posted:** Tue Apr 07, 2015 8:22 am

Keep up the good work Artizle!

It seems the Port temp est IAT/ECT table headers are not displayed properly. I've rescaled mine but in ecuflash its showing stock values (i think)

Artizle · **Joined:** Sun Jan 13, 2013 5:58 am **Posts:** 250

illicit wrote:

Keep up the good work Artizle!

It seems the Port temp est IAT/ECT table headers are not displayed properly. I've rescaled mine but in ecuflash its showing stock values (i think)

Good catch! Everyone using port temp est should double check their tables with these definitions, the old ones were wrong and probably didn't set the values that you wanted to enter.

Danysti86 · **Joined:** Fri Jun 06, 2014 10:44 pm **Posts:** 2

hello I'm Italian, how can I be sure to write this map without risking my wall the ECU, sorry I'm new and I do not speak English well

Artizle · **Joined:** Sun Jan 13, 2013 5:58 am **Posts:** 250

Danysti86 wrote:

hello I'm Italian, how can I be sure to write this map without risking my wall the ECU, sorry I'm new and I do not speak English well

Check the main thread for compatibility info

Here are defs for 3.9.2, as always please report any errors

EDIT: accidentally excluded a lot of the metric tables. Re download if you're using the metric definitions.

Artizle · **Joined:** Sun Jan 13, 2013 5:58 am **Posts:** 250

Definitions for Carberry 4.2.0 blaze it are attached. Make sure you only edit 4.2.0 roms with these as there are important changes that could corrupt the rom. If you used the old defs to edit 4.20 it's best you start over with a fresh copy. As far as I know there are no pop up warnings like in romraider for ecuflash so check the "ROM Version" table and the "Base Ignition Timing X-Axis Definition Check Byte" table before you start editing. Check the help tab within those tables for further clarification.

If you find any errors please report.

Dr Waffles · **Joined:** Wed Oct 23, 2013 9:42 am **Posts:** 252

Dr Waffles · **Joined:** Wed Oct 23, 2013 9:42 am **Posts:** 252

Missing the boost offset for the metric MAP definitions

Also no TD activation threshold RPM.

Artizle · **Joined:** Sun Jan 13, 2013 5:58 am **Posts:** 250

Dr Waffles wrote:

Missing the boost offset for the metric MAP definitions

Also no TD activation threshold RPM.

Should all be fixed now. The conversion for the multiplier from psi to bar was also messed up. If anyone messed with that table using metric defs, double check it with these new defs.

phatron · **Posted:** Sat Aug 08, 2015 8:55 pm

So there is no way to change boost or timing based on ethanol content?

You could set up map 2 to be for pure e85.....but then it would be up to the end user to monitor the ethanol content and make sure they switched back to map1 for lower content.

RomRaider

Forum rules

CarBerry ROM - EcuFlash Definitions

Who is online