 |
RomRaiderOpen Source ECU Tools |
|
RomRaider
Documentation
Community
Developers
|
 
|
Page 1 of 1
|
[ 11 posts ] |
|
| Author |
Message |
|
MikeCL
|
Post subject: 850cc Legacy GT scaling?  Posted: Mon Oct 02, 2017 11:43 pm |
|
 |
| Newbie |
Joined: Sat Nov 08, 2014 12:31 am
Posts: 21
|
|
Anyone know or have info what's a good base to start with as of right now it's hard to get it to idle
|
|
| Top |
|
 |
|
jon7009
|
Post subject: Re: 850cc Legacy GT scaling? Posted: Tue Oct 03, 2017 12:24 am |
|
|
| Senior Member |
Joined: Thu Dec 18, 2014 10:31 pm
Posts: 1529
Location: oregon
|
|
not enough information.
What 850cc injectors are they?
_________________
if you're generous, feel free to donate.
venmo @ jon7009, 1047 when asked
jedilley@gmail.com for paypal
|
|
| Top |
|
|
|
MikeCL
|
Post subject: Re: 850cc Legacy GT scaling? Posted: Tue Oct 03, 2017 5:34 am |
|
|
| Newbie |
Joined: Sat Nov 08, 2014 12:31 am
Posts: 21
|
|
| Top |
|
|
|
MikeCL
|
Post subject: Re: 850cc Legacy GT scaling? Posted: Thu Oct 05, 2017 6:29 am |
|
|
| Newbie |
Joined: Sat Nov 08, 2014 12:31 am
Posts: 21
|
|
| Top |
|
|
|
jon7009
|
Post subject: Re: 850cc Legacy GT scaling? Posted: Thu Oct 05, 2017 8:06 am |
|
|
| Senior Member |
Joined: Thu Dec 18, 2014 10:31 pm
Posts: 1529
Location: oregon
|
|
Don't have any experience with them. I shy away from side feed injector tuning.
I don't know the correct scalar or latency, but you might also need low injector pulse width compensation.
_________________
if you're generous, feel free to donate.
venmo @ jon7009, 1047 when asked
jedilley@gmail.com for paypal
|
|
| Top |
|
|
|
MikeCL
|
Post subject: Re: 850cc Legacy GT scaling? Posted: Fri Oct 06, 2017 5:46 pm |
|
|
| Newbie |
Joined: Sat Nov 08, 2014 12:31 am
Posts: 21
|
|
I might give it a shot tomorrow
|
|
| Top |
|
|
|
MikeCL
|
Post subject: Re: 850cc Legacy GT scaling? Posted: Mon Oct 09, 2017 1:41 am |
|
|
| Newbie |
Joined: Sat Nov 08, 2014 12:31 am
Posts: 21
|
|
Finally was able to pull the stock ROM off the car does anyone have scaling data for the SPT intake for the '05 Legacy GT 5MT? Not sure where I should start with.
|
|
| Top |
|
|
|
bludgod
|
Post subject: Re: 850cc Legacy GT scaling? Posted: Mon Oct 09, 2017 3:58 pm |
|
|
| Moderator |
 |
Joined: Sat Jul 06, 2013 12:55 pm
Posts: 3297
Location: NI
|
|
as per my response in the other thread, easiest way if your just getting started is to do one - adjust the map to suit, then add the other. Probably as handy do do a run, log the actual AFR on your wideband then fit the injectors and adjust the injector scale value until you reach the same AFR again. If the airflow corrections are off at idle then increase/decrease the injector latency until you are back where you where. After that add the intake and do some maf scaling until your back where you where and you should be good to go.
_________________
Good luck and may the logs be ever in your favour!
|
|
| Top |
|
|
|
MikeCL
|
Post subject: Re: 850cc Legacy GT scaling? Posted: Mon Oct 09, 2017 5:06 pm |
|
|
| Newbie |
Joined: Sat Nov 08, 2014 12:31 am
Posts: 21
|
|
Can't I try to get the airflow arf to be as close to stoch as possible at idle as it is now?
|
|
| Top |
|
|
|
MikeCL
|
Post subject: Re: 850cc Legacy GT scaling? Posted: Sun Oct 15, 2017 1:40 am |
|
|
| Newbie |
Joined: Sat Nov 08, 2014 12:31 am
Posts: 21
|
|
I got it I forgot to post it was the injector latency that needed to be changed I changed the 14v to 1.50ms and it idled fine
|
|
| Top |
|
|
|
MikeCL
|
Post subject: Re: 850cc Legacy GT scaling? Posted: Sat Dec 23, 2017 4:24 am |
|
|
| Newbie |
Joined: Sat Nov 08, 2014 12:31 am
Posts: 21
|
|
ok I'm pretty some one of the fuel injectors have crapped out.. this is what I noticed normally idle at 14.7 or so.. now it would be 16+ AFR.. but while in boost around 15 or 12 AFR.. at idle the AFR would be always jumping up and down at least 8 points..
Today when driving on the highway I give it some fuel and I had a huge loud bang and my AFR is full rich at 10.0 AFR no hoses that I can see have came off but with it running full rich it has to be a fuel injector issue?
I noticed the 2300-3000 RPM range I had a a lot of hesitation that would cause the car to buck in the lower gears no matter how smooth you tried to roll on the throttle.
If I don't have to work tomorrow I will try installing the stock injectors again.
|
|
| Top |
|
|
|
|
Page 1 of 1
|
[ 11 posts ] |
|
Who is online |
Users browsing this forum: No registered users and 1 guest |
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum
|
|
|
