RomRaider

Use the regular definitions when using RR's built in Learning View, they work great for me. I've never been able to get RR's Learning View to work with the SDlogger definitions.

I have a problem, and download version 4.2 and put the files of the LOAD folder in the subaru / base folder and in the subaru / imprezasti folder. e patched the speed density map but when loading it with the ecuflash I only see this. What did I do wrong?

this is correct for the load base determination definition. now choose if you want map or maf based load and save your rom. close ECUflash replace the load determination file with the maf or map definition file (depending on your chosen scale). Open ECUflash again then you should see all the tables.

Ive never tried the map/load determination def in ecuflash before. I thought they were only Romraider defs for that area.

how ive done it succesfully.

-Open romraider, set the load determination def in the first spot in def manager.
-Open the carberry base hex and pick load based or maf base. I chose map base to keep everything the same, and becasue i planned to be SD only.
-save and close rom as new name, mines usually the date.
-move the correct def to the top of def manager, mine is the map axis def. load based would be the load axis def
-reopen new rom and you should be good to go.

after that first thing i did was determine my map sensor size and scale the tables and setup boost cut in its operating range. Then i set timing to something safe since fueling may end up all over the place on a virgin VE table

Longtime forum junky, first time forum post-er -

So I have put the load determination files in the correct directories, using either the v3 or v4 defs, with ecuflash v1.44, and I cannot seem to make the load determination option display in Ecuflash. I have already made that determination in RR, is that why? All I get when I load a .bin into ecuflash with the load determination files is the headers of all the sections (anti-lag, fueling Speed Density, Ignition timing, etc). There are no +boxes to choose individual settings, but its the load deter definitions anyhow.

When I put the BASE_load and 4.2 imperial files in the directories, everything is great, just how I edited them in RR. But when I open the check byte option under Ignition timing it says "no match". Is that a problem? The table has the correct values in the load axis. Is it safe to flash?

Also, when I edit a table in a .bin in Ecuflash and save it, that .bin NO LONGER OPENS IN ECUFLASH OR RR! Not cool haha, I have since made extra copies of everything after editing, and haven't edited a thing in Ecuflash.

Since experiencing that loss of opening ability I have become skeptical about flashing the carberry to my 02 USDM AT ECU (I have a MT it's just out of an AT), My OG MAF based rom is doing just great, don't want to brick anything.

i normally do it with a complete copy of the ECUflash folder but I have only the Carberry4.2_Load_determination.xml and CarberryBASE_Load_determination.xml files in the rommetadata folder and nothing else. When you open a carberry rom then you only get the option to pick your load scale. After picking if i want map or load scale then save the file and close ECUflash. Open a regular copy of ECUflash with the regular definition in it and job done I can now edit the scales as needed.

If your getting an error that the file can't be opened there must be something else going on that's messing up the file so double check your definitions and try making a clean copy of your ECUflash folder with only the files you need as quick test.

Wow that took me way too long for something so simple, thanks for your help - Those files that were crashing after saving in Ecuflash were definitely a problem, I just copied the Speed Density Base.hex again and finally figured out how it works, now to copy all the tables back in, Thank you!

For all the next guys out there

DL the v4 defs from first page of this thread
extract em

Put the "Load Determination" folder in
C:\Program Files (x86)\OpenECU\EcuFlash

Remove the "rommetadata" folder from the above location, this is only used with boring normal roms
This will not work with this folder still present

Open Ecuflash, Load your carberry rom, make an X-axis determination, SAVE the file
Close Ecuflash

Remove the "Load Determination" folder and put either the "MAP Axis" or "Engine Load Axis" folder - whichever one you determined you wanted- put it in the same place
C:\Program Files (x86)\OpenECU\EcuFlash


Open Ecuflash, and check to make sure the Ignition axis check byte is determined, and DOES NOT say "no match"

Check the x-axis of your Base Ignition Timing Table, make sure it has the correct values and NOT 0.8 or something in the last column on the right

flash it

OMG or under settings in Ecuflash choose metadata directory and direct it to the right folder I'm so stupid haha

whoop whoop

Thanks again for the quick response

Hello, I have seen you posting answears quite frequently and thats why I've decidet to contact you. I'm newbie to Subaru tuning, my 05 wrx is already Carberry converted. With 2.0 openport I cannot find out how to read the rom vie EcuFlash. (has something to do with ecuflash carberry defs probably). Could you gimme an advice where to find the correct info? The exact place for defs? Thank you in advance.

Hola!
Did you get lucky to read your rom? I’m in the same thing, I’d like to tune my suby but I am not sure how to use carberry

You can usually read your rom using 02wrx read/write method.

But EcuFlash don't always have the definition for it, so your best bet is save the file without the definition, and use RR Editor to edit it, then open it on EcuFlash to write it to the car once you finished editing with RR.