Possible to change frequency of pwm feeding ebcs?????

terryjr · **Posted:** Mon Nov 05, 2018 12:09 pm

played with mine a little yesterday. Hooked it back up compressor to NO, wastegate to COM, and a brass filter in NC port. Im on pump gas so boost set only about 1psi over wastegate. I was having laptop battery issues and couldnt get it turned on log engough to load the right parameters so missed wideband, wgdc and ethanol %. But i guestimate WGDC would have been around 2-3% since i have gasoline at 0% and e85 at 20%. i got a 24psi spike in 3rd and 4th that flatten back out at 20ish. But in good news, i hit 24psi by 4800rpm, down 700 from last year. And that 4800 on pump, should be sooner on E

https://datazap.me/u/terryjr/1st-exotru ... om=538-589

terryjr · **Posted:** Thu Dec 20, 2018 1:49 pm

its spiking like crazy but not from the ebcs. I pulled a spring out so ewg is back to 13psi base pressure. Went for a drive last night and phone died so didnt get a log. Switched my logging over to BtSSM. logs everything romraider does but connects instantly to phone when i plug it into tactrix and have about the same crappy refresh rate. But its way more portable and i can upload to datazap straight from phone without a wifi connection

h82lose91 · **Joined:** Thu Feb 23, 2012 9:16 pm **Posts:** 36

Can someone tell me the location for AZ1G401V
Thanks!

naviuk · **Posted:** Sun Oct 18, 2020 6:38 am

Anyone possibly have the location for A2ZJ500M - From what i found it should be "5ab5e" but that doesn't seem to work :/

throttlehappy · **Posted:** Fri Oct 23, 2020 1:04 am

naviuk wrote:

Anyone possibly have the location for A2ZJ500M - From what i found it should be "5ab5e" but that doesn't seem to work :/

5A5BE works for me with 15.27Hz in EcuFash

pyro6314 · **Joined:** Sun Dec 01, 2013 8:17 pm **Posts:** 47

Would someone mind pulling the BCS Freq & Fuel Pump Freq address for A2ZJE11J (06sti). Thanks

td-d · **Posted:** Thu Nov 05, 2020 9:55 am

pyro6314 wrote:

Would someone mind pulling the BCS Freq & Fuel Pump Freq address for A2ZJE11J (06sti). Thanks

Code:

ROM:000C008A Wastegate_Solenoid_Pulse_Frequency:.data.w h'3FF7

rac · **Joined:** Tue Apr 15, 2008 3:11 pm **Posts:** 162

3 port
settled for 25hz frequency after a series of experiments, as going higher made tuning low boost WG very hard

lvkeith · **Joined:** Sun Jan 02, 2011 10:37 pm **Posts:** 51

Can I please have A2TB002C for waste gate frequency?

Sent from my iPhone using Tapatalk

pyro6314 · **Joined:** Sun Dec 01, 2013 8:17 pm **Posts:** 47

Thanks td-d, wish I had the aptitude to do the same.

The Lorax · **Joined:** Tue Nov 04, 2014 11:51 am **Posts:** 219

lvkeith wrote:

Can I please have A2TB002C for waste gate frequency?

It's c026a (and also in the definitions I've sent you previously!)

lvkeith · **Joined:** Sun Jan 02, 2011 10:37 pm **Posts:** 51

The Lorax wrote:

lvkeith wrote:

Can I please have A2TB002C for waste gate frequency?

It's c026a (and also in the definitions I've sent you previously!)

Ha. Thanks.

Sent from my iPhone using Tapatalk

darksands · **Joined:** Sat Jan 02, 2021 12:18 am **Posts:** 1

Tried searching but is there an address for A4TF810F or A4TF800F? 05 WRX MT. Thanks!

Edit: so i was looking at the carberry definitions which I think are based of 02/03 WRX. The address they have is 0x2c0cd. I used that address and got a table with fuel pump output frequency of 358.17 and wastegate solenoid frequency of 5.40 on the A4TF810F map. Ive read that stock frequency is 10Hz so I am a little weary of changing the value since it doesn't match what is reported. Just wanted to see if anyone can confirm this is the correct address or if someone can make sense of the hex and point me to the correct address. Thanks!

frankenbug · **Posted:** Wed Apr 20, 2022 8:19 am

Edit: Went to Carberry lolz

NiboMan · **Joined:** Mon Aug 17, 2020 4:10 am **Posts:** 13

Can i have the watstegate frequency hz address for A2UH000A, please?
Thanks

RomRaider

Forum rules

Possible to change frequency of pwm feeding ebcs?????

Who is online