 |
RomRaiderOpen Source ECU Tools |
|
RomRaider
Documentation
Community
Developers
|
| Author |
Message |
|
dschultz
|
Post subject: Re: MS42 ECU definitions  Posted: Sat Feb 19, 2022 9:02 am |
|
 |
| RomRaider Developer |
Joined: Wed May 20, 2009 9:49 pm
Posts: 7314
Location: Canada eh!
|
drg458 wrote: dschultz wrote: Fixed MAF table for RomRaider Editor version 0.8.0 Maybe you can post also with ºC instead of ºF? Thankyou!! Which parameters don't have ºC ?
|
|
| Top |
|
 |
|
drg458
|
Post subject: Re: MS42 ECU definitions Posted: Sat Feb 19, 2022 11:43 am |
|
|
| Newbie |
Joined: Thu Dec 10, 2020 11:31 am
Posts: 8
|
dschultz wrote: drg458 wrote: dschultz wrote: Fixed MAF table for RomRaider Editor version 0.8.0 Maybe you can post also with ºC instead of ºF? Thankyou!! Which parameters don't have ºC ? Engine Cooling section
|
|
| Top |
|
|
|
notoriousg
|
Post subject: Re: MS42 ECU definitions Posted: Mon May 02, 2022 7:13 pm |
|
|
| Newbie |
Joined: Wed Jun 10, 2020 12:57 pm
Posts: 5
|
|
Hey, guys.
I have learned a lot thanks to all the great work you have done. Thank you for your enormous contribution.
I decided to post a thread with something i found and i think could be helpful:
The hardcut hysteresis address for 0110AD, 0110CA and 0110C6 i think is wrong.
For CA and C6 partials it is defined as address 0x2f1 and for full flash 0x482f1, but i think it should be 0x2f0 and 0x482f0 respectively.
For AD partial it is 0x2d3 and for full flash 0x482d3, but i think it should be 0x2d2 and 0x482d2 respectively.
Also most MS42 files have the soft limiter hysteresis set to 0 by default, but some have it set to 32 by default, so i edited the latest v0.43 .xml a little and changed
the addresses i think are wrong and also added a new constant for the Softlimiter hysteresis with addresses 0x482EE full and 0x2EE partial for CA and C6 and 0x482D0 full and 0x2D0 partial for AD.
Please let me know what you think.
You do not have the required permissions to view the files attached to this post.
|
|
| Top |
|
|
|
doluc123
|
Post subject: Re: MS42 ECU definitions Posted: Fri May 27, 2022 10:28 am |
|
|
| Newbie |
Joined: Sun May 22, 2022 5:13 pm
Posts: 1
|
|
Hi
I have a problem
When i try to load ms42/43 definitions i alvays see this error
anybody help me?
ms41 definitions work ok
You do not have the required permissions to view the files attached to this post.
|
|
| Top |
|
|
|
dschultz
|
Post subject: Re: MS42 ECU definitions Posted: Fri May 27, 2022 5:44 pm |
|
|
| RomRaider Developer |
Joined: Wed May 20, 2009 9:49 pm
Posts: 7314
Location: Canada eh!
|
Please try this version. v0.44 - Change scaling name to scaling category - includes changes posted here: viewtopic.php?p=165161#p165161
You do not have the required permissions to view the files attached to this post.
|
|
| Top |
|
|
Who is online |
Users browsing this forum: No registered users and 0 guests |
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum
|
|
|
