RomRaider

Hi, I am trying to read a 2007 Subaru Forester 2.0 NA using tactrix openport 2.0, I've tried several cars and protocols, but I cannot read the ECU. I connected the green plug under the dash, and also double-checked if the passenger side is connected or not. Cable-wise, I don't have a problem and they're all connected. I also checked my definitions, they seem to be okay as well. Is there a way to read this ECU?

Here's my EcuFlash log:

[10:11:22.271] scanning for metadata models in C:/Program Files (x86)/OpenECU/EcuFlash/rommetadata
[10:11:26.109] 557 ROM metadata models scanned.
[10:11:34.928] using metadata XML ID read_subarush7058can from file C:/Program Files (x86)/OpenECU/EcuFlash/rommetadata/read templates/read_subarush7058can.xml
[10:11:36.566] using metadata XML ID read_subarush7058can from file C:/Program Files (x86)/OpenECU/EcuFlash/rommetadata/read templates/read_subarush7058can.xml
[10:11:36.605] J2534 API Version: 04.04
[10:11:36.605] J2534 DLL Version: 1.02.4870 Feb 3 2017 23:36:31
[10:11:36.605] Device Firmware Version: 1.17.4877
[10:11:36.605] Device Serial Number: TAyNcRtB
[10:11:40.942] kernel get version
[10:11:41.204] VIN : JF1SG5LE57G115231
[10:11:41.345] CVN : F0CEBFDB
[10:11:41.365] Requesting Seed...
[10:11:41.386] interface close
[10:11:41.391] interface close
[10:11:52.134] using metadata XML ID read_sti05 from file C:/Program Files (x86)/OpenECU/EcuFlash/rommetadata/read templates/read_sti05.xml
[10:11:52.143] using metadata XML ID read_sti05 from file C:/Program Files (x86)/OpenECU/EcuFlash/rommetadata/read templates/read_sti05.xml
[10:11:53.837] using metadata XML ID read_sti05 from file C:/Program Files (x86)/OpenECU/EcuFlash/rommetadata/read templates/read_sti05.xml
[10:11:53.854] J2534 API Version: 04.04
[10:11:53.854] J2534 DLL Version: 1.02.4870 Feb 3 2017 23:36:31
[10:11:53.854] Device Firmware Version: 1.17.4877
[10:11:53.854] Device Serial Number: TAyNcRtB
[10:11:58.508] kernel get version
[10:11:58.711] interface close
[10:11:58.755] J2534 API Version: 04.04
[10:11:58.755] J2534 DLL Version: 1.02.4870 Feb 3 2017 23:36:31
[10:11:58.755] Device Firmware Version: 1.17.4877
[10:11:58.755] Device Serial Number: TAyNcRtB
[10:11:58.935] interface close
[10:11:58.955] J2534 API Version: 04.04
[10:11:58.955] J2534 DLL Version: 1.02.4870 Feb 3 2017 23:36:31
[10:11:58.955] Device Firmware Version: 1.17.4877
[10:11:58.955] Device Serial Number: TAyNcRtB
[10:11:59.120] SSM2 init
[10:11:59.364] SSM2 ECU ID is 4E44307106
[10:12:01.452] interface close
[10:12:01.457] interface close

That is Hitachi ECU so EcuFlash won't read it. My open source software will support this ECU at some point near future.

What are you trying to do?

I can tune them remotely using Teamviewer