RomRaider

Hi folks,

I can not establish connection via both 2.0 genuine and clone (gold pin) tactrix cables. Would appreciate your support.

Error sending init: Parameter portName must not be null or empty

Do I need to create a virtual com port?

Also, whenever I try to do a fresh RR install, I notice that uninstaller doesn't function, new installation may create desktop shortcuts or not. Following the installation, my definitions are still there as if iti s not a clean install.

What am I missing here?

System is win 10 64bit. RR and JRE 32 bit. Open port 2.0 64 bit drivers.

Thanks in advance for your help!

This issue occurs with connection to 04 STI (EDM) Ecudit admin can extract the rom just fine and their logger works too. What could I be missing here? Any help is appreciated!

11:06:17,009 DEBUG [Query Manager] - QueryManager started.
11:06:17,009 INFO [Query Manager] - J2534 Library names loaded from file: ./customize/j2534Libraries.properties
11:06:17,314 DEBUG [Query Manager] - Found J2534 Vendor:Tactrix Inc. - OpenPort 2.0 J2534 ISO/CAN/VPW/PWM | Library:C:\WINDOWS\SysWOW64\op20pt32.dll
11:06:17,314 INFO [Query Manager] - Trying new J2534/ISO9141 connection: Tactrix Inc. - OpenPort 2.0 J2534 ISO/CAN/VPW/PWM
11:06:17,361 INFO [Query Manager] - J2534 Version => firmware: 1.17.4877, dll: 1.01.4341 Jul 10 2014 14:16:35, api: 04.04
11:06:17,361 DEBUG [Query Manager] - J2534/ISO9141 set connection properties: bits=8, parity=0
11:06:17,376 DEBUG [Query Manager] - J2534/ISO9141 success: deviceId:1, channelId:3, msgId:0
11:06:17,376 INFO [Query Manager] - J2534/ISO9141 connection initialised
11:06:17,376 DEBUG [Query Manager] - J2534/ISO9141 stopped message filter:0
11:06:17,376 DEBUG [Query Manager] - J2534/ISO9141 disconnected channel:3
11:06:17,376 INFO [Query Manager] - J2534/ISO9141 closed connection to device:1
11:06:17,376 ERROR [Query Manager] - Error sending init: SSM
11:06:17,376 INFO [Query Manager] - Trying serial connection...
11:06:17,383 ERROR [Query Manager] - Error sending init: Parameter portName must not be null or empty

Still looking for a solution

Applied some changes to driver directories and reg edit. tested another cable but nothing new.

- Found J2534 Vendor: Tactrix OpenPort 2.0 | Library:C: \J2534\op20pt32.dll
Trying new J2534/IS09141 connection: Tactrix OpenPort 2.0
J2534 Version => firmware: 1.17.4877, dll: 1.02.4870 Feb 3 2017 23:36:05, api: 04.04
J2534/IS09141 set connection properties: bits=8, parity=0
J2534/IS09141 success: deviceId:1, channelId:3, msgId: 0
J2534/IS09141 connection initialised
J2534/IS09141 stopped message filter:0
J2534/IS09141 disconnected channel:3
J2534/IS09141 closed connection to device:1
Error sending init: SSM
Trying new J2534/IS09141 connection: Tactrix Inc. - OpenPort 2.0 J2534 ISO/CAN/VPW/PWM
J2534 Version = Firmware: 1.17.4877, dll: 1.02.4870 Feb 3 2017 23:36:05, api: 04.04
J2534/IS09141 set connection properties: bits=8, parity=0
J2534/IS09141 success: deviceId:1, channelId:3, msgId:0
J2534/IS09141 connection initialised
J2534/IS09141 stopped message filter:0
J2534/IS09141 disconnected channel:3
J2534/IS09141 closed connection to device:1
Error sending init: SSM
Trying new J2534/IS09141 connection: Windows J2534 OP2 WinUSB
J2534 Version => Firmware: 1.17.4877, dll: 1.02.4870 Feb 3 2017 23:36:05, api: 04.04
J2534/IS09141 set connection properties: bits=8, parity=0

Tested with all protocol options available in v370 definitions file and carberry logger definition. What could be the culprit here?

Thx!

no you dont need to create a com port, but try removing all your ecuflash settings and install folder then installing again the latest version from their website.

are you able to log the car at all to confirm there's nothing unusual about it?

Hi thanks for reply!

I tried removing ecuflash entirely and even anything related with it found in registry.

I can easily log the car using ECUedit logger and scanner devices can establish connection too.