RomRaider

I think i found some of the RPM Resume thresholds below. Having pulled the roms apart yet but im 99% these are right so far. Good starting point if someone has their rom broken down.

05 OUTBACK XT A2WC552S
2D: C8100
X: C7470

08WRX AZ1E401A
2D: CB348
X: C8AD8

09WRX AZ1G401V
2D: CB934
X: C9098

NEED TO CHECK LAST ONE.

2010 WRX AZ1G701V
2D: CBE80
X: C95F4

Requesting for 06 EDM wrx A8DH200Y and 03 JDM Sti A4TE002C

On A8DH200Z:




<table name="TipOut - RPM Delta Activation" category="Idle Control" address="c6328" type="1D" level="1" scaling="rawecuvalue">
<description>RPM delta required for overrun mode to kick in</description>
</table>

<table name="TipOut - IPW" category="Idle Control" address="c632c" type="1D" level="1" scaling="ms">
<description>IPW apllied when injectors are re-opened = Tip-out</description>
</table>

<table name="TipOut - RPM thresholds Fuel resume" category="Idle Control" address="c7644" type="2D" level="1" scaling="Overrun Fueling">
<description>when RPM goes below these thresholds, injectors are re-opened</description>
<table name="ECT" address="c6508" type="X Axis" elements="16" scaling="CoolantTemp(DegreesC)"/>
</table>

<table name="TipOut - thresholds FuelCut" category="Idle Control" address="c6374" type="2D" level="1" scaling="RPM">
<description>Set of rpm thresholds that are used by multiple counters in determining when fuel cut will happens during overrun mode</description>
<table name="X" type="Static X Axis" elements="3">
<data>Low</data>
<data>Med</data>
<data>High</data>
</table>
</table>

On A8DH200Y:

<table name="TipOut - RPM Delta Activation" category="Idle Control" address="c62A8" type="1D" level="1" scaling="rawecuvalue">
<description>RPM delta required for overrun mode to kick in</description>
</table>

<table name="TipOut - IPW" category="Idle Control" address="c62AC" type="1D" level="1" scaling="ms">
<description>IPW apllied when injectors are re-opened = Tip-out</description>
</table>

<table name="TipOut - RPM thresholds Fuel resume" category="Idle Control" address="c75C4" type="2D" level="1" scaling="Overrun Fueling">
<description>when RPM goes below these thresholds, injectors are re-opened</description>
<table name="ECT" address="c6488" type="X Axis" elements="16" scaling="CoolantTemp(DegreesC)"/>
</table>

<table name="TipOut - thresholds FuelCut" category="Idle Control" address="c62F4" type="2D" level="1" scaling="RPM">
<description>Set of rpm thresholds that are used by multiple counters in determining when fuel cut will happens during overrun mode</description>
<table name="X" type="Static X Axis" elements="3">
<data>Low</data>
<data>Med</data>
<data>High</data>
</table>
</table>

Could someone find the addresses for AZ1G300F?

Thanks in advance.

Thanks a lot!!

Is this the correct code for my rom?? I am getting some strange rpm values in the first table.

<rom>
<romid>
<xmlid>A2ZJB11J</xmlid>
<internalidaddress>2000</internalidaddress>
<internalidstring>A2ZJB11J</internalidstring>
<ecuid>3D12594106</ecuid>
<year>05</year>
<market>USDM</market>
<make>Subaru</make>
<model>Impreza</model>
<submodel>STi</submodel>
<transmission>MT</transmission>
<memmodel>SH7058</memmodel>
<flashmethod>sti05</flashmethod>
<checksummodule>subarudbw</checksummodule>
</romid>
<include>32BITBASE</include>

<table name="Overrun Fueling RPM Resume Threshold" address="C6C68" type="2D" level="1" scaling="RPM">
<table name="X" address="C60F4" type="X Axis" elements="16" scaling="DegreesF"/>
</table>

<table name="Overrun Enrich RPM Delta Activation" address="C5FE4" type="1D" level="1" scaling="rawecuvalue"/>

<table name="Overrun initial injector enrichment (pulsewidth)" address="C5FE8" type="1D" level="1" scaling="ms"/>

<table name="Overrun Fueling Cut Counter RPM Threshold" address="C6014" type="2D"
level="1" scaling="RPM">
<table name="RPM" type="Static X Axis" elements="3">
<data>Low</data>
<data>Med</data>
<data>High</data>
</table>
</table>

Those are correct - -17 RPM delta, 0 initial enrichment, counters are 2000, 2500 and 3000 RPM, and tables goes down from 2400 to 950 RPMs.

The stock values that show up in RPM do not reflect those numbers.

Well - that's the table:

Check whether your scaling / template is correct.

Forgive me for asking. I am not a developer. Please help me understand where/what I need to do with this information. I understand how to cut/paste code like I posted but I do not understand where to utilize this information you just posted. A point in the right direction is all I really need.

Thanks in advance.

That is a lookup table, and the following lines represent the Axis and Data addresses.



First line indicates the table has 16 entries.

The problem exists in your table's scaling.

From Github Alpha definition 32BITBASE:

Thanks Merp. STI2NR, plug the addresses into the above template and paste into your Ecuflash XML, that should sort you out.

Thanks Merp and td-d for your valuable time. That fixed the issue I was having. A little help goes a long ways.